DB1.2 1Ohm Class D Monoblock Subwoofer 12v Power Amplifier 1000w RMS

ASSAULT

World RRP: £194.99

Category: AMPLIFIERS

Product code: DB1.2

Product description

Now shipping Version 4 of this product - The new circuit board also allows us to announce 1 ohm stability which further broadens the range of system applications and subwoofer configurations that DB1.2 can be used in. The new DB1.2 offers its user an outstanding balance of power and sound quality. The DB1.2 was developed specifically to be a heavier duty version of the DB1.1. Building on the series architecture of an oversize power supply and efficient heat-sink design the DB1.2 will run hard for extended listening periods without being overworked. With Class D topology, the DB1.2 is highly efficient in power exchange and delivery; less power wasted, less heat generated, less distortion and longer service life. The circuit design is robust enough to deliver powerful bass while remaining poised and refined, producing a balanced accurate sound across the full bass audio spectrum. At detail level we included 2 positive and 2 negative speaker terminals making it easier for you to connect two subwoofers or dual voice coil subwoofers to the one amplifier. Naturally there is a full set of sound controls; variable low pass, variable subsonic filter and a parametric bass boost (frequency and level). For those tracks that deserve “just that bit extra” we also included a wired cockpit bass remote for on the fly adjustment.

V1 – The V1 production model had a short life and only 300 units were produced. V2 – Moved production to a new facility and changed the design completely. Featured increased power output and ability to link 2 amps to one output. V3 – Addressed the issues with phase alignment making it complicated to link 2 amps and simplified this. It also added better terminals and different remote control, as well as slightly higher power output. V4 – 2016 styling badge, as well as increased overall performance. 16v ready. Quoted theroetical output figures revised after testing. We did discuss a V5 model which was to be the same but with a fan to lower running temperatures under heavy load. We changed our mind about this and instead created the DB1.2s with more power for those applications where running a V4 DB1.2 would have really pushed the board to the limit.

Product Category Amplifiers
Version 4
Series Assault
Barcode 700175821683
Product Net Weight (g) (For Pairs/Sets Weight Is All Major Parts) 3150
Product Height (mm) 62
Product Length (mm) 280
Product Width (mm) 242
Complete Product Pack Weight (g) 3520
Retail Carton L (mm) 298
Retail Carton W (mm) 243
Retail Carton H (mm) 98
Warranty (Months) 12
Sold As Single

Quoted Maximum Unfused Power, No THD Limit (Watts) 2000
Quoted Maximum Unfused RMS, No THD Limit (Watts) 1000
Quoted RMS Per Channel 4Ohm, No THD Limit (Watts) 500
Quoted RMS Per Channel 2Ohm, No THD Limit (Watts) 750
Quoted RMS Per Channel 1Ohm, No THD Limit (Watts) 1000
Verified RMS 14.4V Per Channel 4Ohm (Watts)@(THD), (Amps), (Version) 403@1%, 33.8 (V4), 313@1%, 25.2 (V3)
Verified RMS 14.4V Per Channel 2Ohm (Watts)@(THD), (Amps), (Version) 670@1%, 58.9 (V4), 540@1%, 45.4 (V3)
Verified RMS 14.4V Per Channel 1Ohm (Watts)@(THD), (Amps), (Version) 1004@3%, 102.4 (V4), 809@1%, 76.3 (V3)
Frequency Response (Hz) 10-1000
THD Continuous 4 Ohm 1Khz/100Hz (%) <0.1
Signal To Noise Ratio (db) >96
LPF (Hz) 40-180
Bass Boost (Db) 0-12
Boost Frequency (Hz) 30-80
Subsonic Filter (Hz) 15-50
Audio Signal Input Voltage (V) 0.2-6
LPF Slope (Db/Oct) 12
Subsonic Filter Slope (Db/Oct) 12
Amplifier Topology Class D
Amplifier Strappable? Not Recommended - No Warranty 2Ohm
Fuse Rating (Amps) 120
Power Wire Input Gauge (AWG) 4
Recommended Wiring Kit and Accessories PWK4.1 RCA5.1
Minimum Recommend Final Load Per Channel (Ohms) 1

  • Latest Version Of Our Mid Range Compact Mono
  • Highly Efficient Class D Topology
  • Variable Bass Boost Level and Frequency
  • Variable Low Pass Filter
  • T.D.O.S. Amplifier Protection Circuitry
  • Variable Subsonic Filter
  • Up To 6V Ready Pre Amp Input Stage
  • O.P.S. Oversized Power Supply
  • Thermally Efficient Heatsink Coating
  • Low THD Audiophile Components
  • High Density Cast Aluminium Heatsink Body

  • 1 x High Performance Mono Amplifier
  • 1 x Bass remote level control
  • 1 x 5m level control cable
  • 4 x Self tapping screws

Downloads

Contact us about this product

If you have any questions about this product, complete the form below and we’ll get back to you as soon as we can.

Fields marked with an * are mandatory